So what’s the difference?

The common misconception, created by most big box home improvement stores, is that installing epoxy is a simple process. “Just roll it on and sprinkle a few chips in it and it will last a lifetime”, they tell you. But it’s really not that simple, and I'm going to explain why.

The short answer is this: DIY Consumer-grade epoxy is thin, not prepared correctly and almost never has a protective topcoat.

Store-bought epoxy is a water-based material that is usually around 50% solid, which means that half of the product evaporates into the air. When you roll this product onto the floor, after it cures, it leaves behind a very thin coating on the floor. Most of these generic consumer epoxies even go so far as to claim that one gallon will cover a 1 car garage. Assuming that a 1 car garage is around 400 feet, that means that the coating would only be 2.4 mils thick… which translates to 2.4 thousandths of an inch.  They also recommend a top coat of epoxy, which means the entire finished floor is around 5 mils thick.

Our 100% solids epoxy goes down around 10 mils thick for the first coat, and 15 mils for the second coat. Then we apply a third coat of urethane. What this all means is that when our entire epoxy system has been installed, the chemicals (epoxies & urethanes) go down approximately 5 times thicker than consumer-grade epoxy systems.

Comparison of a 2 car DIY Epoxy Garage kit vs. the materials we recently used on a 2 car garage:

The most noticeable difference when you compare our process to the DIY hardware store kits is the number of chips and products used. A typical DIY epoxy kit comes with 8 ounces of chips the container is about the size of a Pepsi can and not mention comes with NO protective topcoat. Homeowners are expected to broadcast a cup of chips evenly across an entire garage. It’s nearly impossible to achieve an even look on the floor with such a small quantity. As a side note FULL BROADCAST FLAKE SYSTEMS like we provide, add an additional layer of protection and beauty to that of a granite look. O.K. back to the article...  Homeowners don’t usually have the special spiked shoes, so they are tasked with rolling epoxy and stopping to occasionally broadcast chips at the same time. It’s an impossible task because like I said before, once you mix the epoxy, the clock is ticking.

A Few Ounces vs. 100+ lbs.

On a typical 500 square foot garage, we usually broadcast somewhere around 75-100 pounds of chips. We are able to broadcast this many chips at the end because we walk around on the epoxy with spiked shoes. Instead of trying to apply 8 ounces of chips evenly, we are able to completely cover the floor in chips (referred to as “broadcasting to rejection”), and then we just vacuum up any excess after the epoxy cures.

 

Floor Preparation.

The next issue we see a lot of is almost no floor preparation sweeping, power washing, or shop vacuuming is not enough to get the epoxy to stick.

We have a process that creates an unbreakable mechanical bond to the concrete for maximum wicking penetration that will last a lifetime. 

Our Process

To prep your floor, our crew uses a diamond grinder that will open the pores of the concrete, to ensure a more permanent bond application.
We vacuum clean dust & particles from the floor, cracks, and corners to ensure a proper bond can take place in every spot and if needed rinse to get any remaining debris.
A moisture barrier primer coat is used as a preventative measure. After a 4-6-hour dry time, holes and cracks are patched/filled if needed.
A solid color epoxy base coat is applied to the concrete surface. Our team then broadcasts color flakes selected by the customer.
We then apply two clear coat layers with the final coat being an industrial-grade polyaspartic system. This further ensures a UV protected floor as well as abrasion and chemical resistance.
With the completion of our installation process, please wait 4-6 hours after the final coat is applied for foot traffic and 24 hours for vehicle traffic.

You can’t just roll on epoxy.

Epoxies are not like regular paint. You don’t just open the can and roll it on. Epoxy is sold as a 2 part mix. One part contains the resin, and the other part contains the hardener. You have to mix these two parts together to get the epoxy ready to apply on the garage floor. Once the epoxy has been mixed, you have a very small window of time to get the epoxy out of the can and rolled out on the floor.

I can’t tell you how many times I’ve gotten calls from homeowners who ask me how we get the epoxy rolled out on the floor before it gets hard. How is it possible to roll a 500 square foot garage in 15-20 minutes? For homeowners or in-experienced contractors with a paint pan, it’s next to impossible.

Professional & Efficient Crews

It takes an entire crew to properly apply epoxy to a garage floor.

When our crew of 3 to 5 people shows up to install an epoxy garage floor, we take the first hour to set up everything perfectly. All of the epoxies are pre-measured and all of the tools that we need are laid out and ready. Everything has to be in its place, because once we mix the epoxy, the clock is ticking, and we have to get the garage floor covered. Each person has a specific job to do:

• One person’s sole job is to mix the epoxy and keep the surrounding area clean.
• One or two people are responsible for troweling the epoxy across the floor. Our epoxy is 100% solid, so you can’t just roll it on because it's thick like honey.
• One or two people are responsible for rolling over the epoxy after it has been spread on the garage floor. They walk on the wet epoxy with special cleated shoes.

• One or two people are responsible for the flake broadcasting for solid and even coverage that adheres to the epoxy before the floor no longer accept flakes due to the quickly drying epoxy.

 

I hope we have answered any questions you may have, If you do have any questions or concerns feel free to reach out to us at any time, we're here to help. 

 

Chris and Keri Davidson | Founders

CONTACT US FOR MORE INFO

Schedule Your FREE Quote.
It takes less than (1) minute.

Why Choose Us?

+ Years In The Flooring Industry
+ Thousands of Floors Installed
+ Most Floors Installed Within 1-3 Days.
miles Our Service Area Distance